As mentioned in yesterday’s post about my Agilent 34461A multimeter purchase, I own quite a few multimeters. Multimeters, whether they cost $20 or $1200, require probes to measure voltage, current*, resistance, and other electrical properties, and probes are connected to multimeters using test leads.
*Except for clamp-on current meters.
Advertisement
Sometimes probes are permanently attached to test leads, other times test leads are modular so that different accessories can be connected to them.
When you buy a new multimeter, it will probably come bundled with test leads and possibly even a few attachments. There’s nothing wrong with using those test leads for basic measurements, but your needs might require you to purchase additional or different test leads separately or later on.
I have purchased a couple of test leads over the years, such as the very economical Extech TL809 kit (via Amazon) and Pomona 5901B straight-end kit (via Amazon).
Test leads are rated for different power levels and are available in different lengths, with different plug shapes, and with different insulating materials.
There are generally two types of test leads widely available – those with PVC insulation jacketing, and those with silicone insulation jacketing. At least one brand (Fluke) also offers heavy duty test leads with EPDM rubber insulation.
PVC vs. Silicone, What’s the Difference?
PVC-insulated test leads are often reasonably durable, flexible, and economically priced.
Advertisement
According to TestPath’s online catalog, PVC test lead wire costs about half as much as silicone test lead wire.
Additionally, PVC wire insulation typically contains phthalate plasticizers and lead-based compounds as stabilizers to improve its flexibility. Phthalates and lead both present potential health issues.
Silicone-insulated test leads are more flexible, more heat and burn resistant, more chemical and solvent resistant, and less sensitive to environmental temperatures.
Silicone-jacketed test leads are more expensive than those made with PVC insulation, and some users don’t like how it can make them feel sticky. The soft stickiness of silicone test leads also make them a little more prone to tangling.
Without question, I very strongly prefer silicone test leads over PVC leads, as I like the greater flexibility and softer touch of the wires and probe handles. Yes, silicone test leads cost appreciably more than PVC leads, but luckily test leads don’t need to be replaced too often.
If you ever want to replace your multimeter’s basic PVC test leads, here are a few inexpensive options:
Fluke TL71 Premium Leads with Built-in Probe (via Amazon)
Fluke TL224 SureGrip Test Leads (Modular probe not included) (via Amazon)
Probemaster 8000 Series Leads 8017S (via Probemaster)
Probemaster 9101 Starter Modular Leads (via Probemaster)
I have not yet used Probemaster or Fluke test leads, although Fluke does own Pomona, but both brands seem to be very well respected.
Billy
PVC just feels like cheap wire to me, I have and prefer to use silicone.
Julian
Can you recommend any test leads that are repairable, either end of the leads or only one end that can be fixed when the wire inside breaks down..
What make are those tensting leads up at the top of this review?
Wayne R.
Silicone test lead insulation (and silicone AC extension cord jackets) are great in cold temps where plastic gets stiff – silicone stays very pliable when cold.
Jeff
I was just on ebay and the Chinese vendors are selling ” silicone pvc”, whatever the heck that is. I see 10A and 20 amp, as well. I thought they were all #18. I guess not. I have a good meter but keep a bunch of HF freebies scattered around but the cables are garbage and do not last. I was looking for some replacements that would last a bit longer but it hardly pays to put premium leads on those cheap meters. The big advantage of silicone, besides flexibility is a high melting point. It is really easy to have a cable get too close to a soldering iron. Ask me how I know. LOL.
Steve
So I am having trouble finding test leads made of the edm rubber. I’m an electrician and my fluke clamp meter originally came with edm rubber. Where can I find another set of these? Thanks for any help.
Stuart
Fluke’s TL27 test leads are made with EPDM rubber insulation. You can find them at Amazon for $40 or at other Fluke dealers.
Bare test lead wire is also available (NTE Electronics red wire, NTE Electronics black wire) for users who might want to create their own cables.
Steve Sheffler
Thanks for the info. Found a guy online that makes quality test leads. No junk alot cheaper then fluke sells for and he makes custom leads as well.